This is the initial release for the UniFi Travel Router Long-Range.

Additional information

Minimum required UniFi mobile app versions:

• iOS: 10.37.1
• Android: 10.39.7

———

If you encounter any issues with this release, please provide us with some details on your setup and connecting client devices.

• Added LCM management support. *
• Added AmneziaWG support for WireGuard. *
• Improved the WiFi uplink roaming algorithm to reduce roaming between access points.

Bugfixes

• Fixed an issue where switching between OpenVPN and Teleport could cause the UTR to become unresponsive.
• Fixed an issue where Teleport failed to recover after WiFi uplink reconnection.
• Fixed an issue where captive portal detection failed.
• Fixed an issue where configuring a static IP address for Ethernet could cause the LCM to remain in the searching state.

Additional information

Minimum required UniFi mobile app versions:

• iOS: 10.31.3
• Android: 10.33.0

* Mobile app support will be added in a future release.

———

If you encounter any issues with this release, please provide us with some details on your setup and connecting client devices.

• Added support for Saved VPN profiles.
• Enhanced support for off-network WAN gateways.
• Improved auto recovery mechanism for Teleport.
• Improved WiFi Uplink roaming.
• Improved WiFi Uplink stability.
• Improved OpenVPN throughput.
• Improved USB tethering compatibility across various devices.
• Improved USB tethering for iOS by preserving trust data across reboots.
• Improved configuration changes to avoid interrupting client connections.
• Improved dashboard data accuracy during configuration changes.
• Improved system stability while scanning for WiFi Uplink candidates.
• Improved stability.

Bugfixes

• Fixed an issue where WiFi Uplink can’t be switched from a Secured SSID to an Open SSID.
• Fixed an issue where WiFi Uplink roaming scan might cause momentary latency.
• Fixed an issue where WiFi Uplink can't connect to WiFi 7 APs with SAE-EXT-KEY or SAE-H2E enabled.
• Fixed an issue where WiFi Uplink might prefer 2.4 GHz on cold-boot.
• Fixed an issue where LCM reports Internet Online but traffic is actually blocked.
• Fixed an issue where LCM does not display VPN icon when OpenVPN is connected.
• Fixed an issue where creating Secondary WiFi did not take effect.
• Fixed an issue where setting a static IP will force UTR offline.
• Fixed an issue where UTR could not be managed in the mobile app under heavy load.
• Fixed issues where OpenVPN might fail to be disabled, enabled, or recover an existing connection.
• Fixed an issue where OpenVPN might fail to connect due to a missing CA.
• Fixed an issue where USB Tethering failed to work after disconnecting WiFi Uplink.
• Fixed an issue where WiFi Uplink can’t connect after a configuration change.
• Fixed an issue where UTR would fail to roam occasionally.
• Fixed an issue where captive portal access was blocked by VPN Kill Switch.
• Fixed an issue where a recovery mode firmware upload did not clear the existing user configuration.
• Fixed an issue where the dashboard showed no connection while UTR was connected.
• Fixed an issue where connecting to a secured WiFi Uplink network failed after using an open network.
• Fixed an issue where UTR always used open networks for WiFi Uplink.
• Fixed an issue where UniFi APs could report UTR as a rogue AP.
• Fixed an issue where changing the Secondary WiFi configuration on UTR could affect the Primary WiFi.
• Fixed an issue where WireGuard could get stuck in a connecting state after being disabled.
• Fixed an issue where custom DNS settings were not always used.
• Fixed a DNS leak when VPN DNS overlapped with the UTR LAN IP.
• Fixed an issue where boot could get stuck if a firmware upgrade was interrupted.

Additional information

Minimum required UniFi mobile app versions:

• iOS: 10.31.3
• Android: 10.33.0

* Mobile app support will be added in a future release.

———

If you encounter any issues with this release, please provide us with some details on your setup and connecting client devices.

• Improved boot time.
• Improved WiFi uplink connection speed and overall WiFi connectivity.
• Improved USB tethering compatibility across various devices.
• Improved apply time for LAN and country configuration changes.
• Added support for same-SSID roaming for WiFi uplink.
• Added support for Saved Networks and roaming for WiFi uplink. *
• Added support for OpenVPN. *
• Added support for internet latency reporting. *

Bugfixes

• Fixed issues connecting to SSIDs containing special characters.
• Fixed display issues caused by special characters.
• Fixed incorrect WireGuard uptime reporting.
• Fixed an issue where VPN Kill Switch continued blocking traffic after reconnection.
• Fixed an issue where VPN Kill Switch failed to block traffic when the VPN connection dropped.
• Fixed WAN/LAN conflict detection with Secondary Broadcast in use.

Additional information

Minimum required UniFi mobile app versions:

• iOS: 10.31.3
• Android: 10.33.0

* Mobile app support will be added in a future release.

———

If you encounter any issues with this release, please provide us with some details on your setup and connecting client devices.

• Improved boot time.
• Added support for WPA2/3-Enterprise networks as Wi-Fi uplink. *
• Added support for Secondary Wi-Fi Broadcast. *

Bugfixes

• Fixed an issue where the DHCP client was sometimes not disabled.
• Fixed WireGuard PSK configuration support.
• Fixed an issue where the VPN would not disconnect when the originating uplink went down.
• Fixed an issue causing unexpected periodic uplink wifi scans.

Additional information

Minimum required UniFi mobile app versions:

• iOS: 10.31.3
• Android: 10.33.0

* Mobile app support will be added in a future release.

———

If you encounter any issues with this release, please provide us with some details on your setup and connecting client devices.

• Improved boot time.
• Added support for per-uplink TTL configuration. *

Bugfixes

• Fixed an issue where the LCM could get stuck.
• Fixed an issue where Wi-Fi uplink could sometimes fail to scan DFS channel SSIDs.
• Fixed an issue where WireGuard would attempt to connect even when a captive portal was present.
• Fixed an issue where WireGuard would repeatedly fall back to WAN due to prolonged missing handshakes.
• Fixed an issue where restoring to default settings could get stuck.

Additional information

Minimum required UniFi mobile app versions:

• iOS: 10.31.3
• Android: 10.33.0

* Mobile app support will be added in a future release.

———

If you encounter any issues with this release, please provide us with some details on your setup and connecting client devices.

• Improved Teleport connection establishment.
• Improved detection for various captive portal implementations.
• Improved device boot time.
• Display unique names for Teleport servers in the client list.
• Added support for VPN Kill Switch. *
• Added support for MAC address randomization when uplinking to WiFi. *
• Added support for MAC address cloning. *

Bugfixes

• Fixed an issue where the wireless uplink connection could be lost after configuration changes.
• Fixed an issue preventing changes to the Wi-Fi uplink configuration.
• Fixed a false positive radar detection event.

Additional information

Minimum required UniFi mobile app versions:

• iOS: 10.31.3
• Android: 10.33.0

* Mobile app support will be added in a future release.

———

If you encounter any issues with this release, please provide us with some details on your setup and connecting client devices.

• Prioritized 5 GHz when the target BSS signal level is greater than -72 dBm.
• Improved 2.4 GHz connectivity for wireless uplink.
• Improved Teleport connection reliability.

Bugfixes

• Fixed an issue where LCM status updates were slower than the mobile UniFi app.
• Fixed an issue where LCM did not display the latest SSID during connection.
• Fixed an issue where SSIDs or passwords containing special characters were not handled correctly.
• Fixed an issue where the uplink monitor was disabled when reconnecting to the same SSID.
• Fixed an issue where manual DNS configuration was not working.

Additional information

Minimum required UniFi mobile app versions:

• iOS: 10.31.3
• Android: 10.33.0

———

If you encounter any issues with this release, please provide us with some details on your setup and connecting client devices.

This is the initial release for the UniFi Travel Router.

Additional information

Minimum required UniFi mobile app versions:

• iOS: 10.31.3
• Android: 10.33.0

———

If you encounter any issues with this release, please provide us with some details on your setup and connecting client devices.